Just How to Replace a Bathtub
Just How to Replace a Bathtub
Blog Article
Just how do you actually feel in regards to Tools You Need to Install a New Bathtub ?
Installing a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old tub is conveniently obtainable, the job can move quickly; if you need to open up a wall to remove the old tub and also position the new bath tub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will require an assistant to move out the old bathtub as well as set in the new one. See to it you have actually qualified on your own for the task and fit trying it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration employing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will aid you set up a brand-new bathtub in your restroom if you have currently bought a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist must comprise the following:
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the tub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, switch on the taps to drain any type of water remaining in the system. The process of removing the existing taps can be quite problematic due to the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the tub in the required position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level and adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Finally, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been made use of at least when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, bring about difficulties with wetness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can break relatively early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece of writing about How to Install a Bathtub Yourself while doing research the web. Sharing is nice. Helping people is fun. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
This Post Report this page